1965 Ford Mustang
14
Builds
49
Knowledge
73
Parts
79
Tools
Builds
This 65 Mustang Keeps Throwing Curveballs
3/28/2026
Basic dash build and small rewire of my 65 Mustang
4/27/2026
F100 Driveshaft Transformed into Mustang Custom Build
6/14/2026
My 65 Mustang Test Drive Exposed Major Issues
5/13/2026
I Installed a Bluetooth Radio in My 1965 Mustang
2/26/2026
Everything I've Done to My 65 Mustang
2/26/2026
65 Mustang first test drive - fuel pressure trouble
7/18/2026
65 Mustang AN fuel line leaking diagnosis
8/5/2026
65 Mustang oil change almost turned into a disaster
8/3/2026
Installing a new aluminum driveshaft in a 65 Mustang
6/20/2026
65 Mustang Evil Energy Fuel filter and shutoff install
8/13/2026
Wednesday Morning Silent drive in the 65 Mustang
9/2/2026
Test driving the 65 Mustang - Houstan we have Problems!
5/27/2026
65 Mustang fuel tank replacement
8/22/2026
Knowledge
How should I dispose of the old fuel and tank?What torque should I use on the driveshaft flange bolts?What safety steps should I take before starting?Can I keep the original radio and still add Bluetooth?What were the most critical problems found on the test drive?How can I safely check for leaks after repair?Can I use an F100 driveshaft in my '65 Mustang?How do I determine the correct driveshaft length?What size U-joints do I need?What does 'throwing curveballs' mean for the project?How do I know if the fuel pump is bad on a 1965 Mustang?How do I tell if the problem is fuel pressure and not ignition or carburetor tuning?What oil viscosity should I use for a 1965 Mustang?How much oil does a 1965 Mustang take?What commonly causes an AN fuel line to leak?What size AN fitting do I need for my 1965 Mustang?Can I reuse my AN fittings or should I replace them?How should I protect and organize the new wiring?Can these issues be fixed cheaply or will it cost a lot?What safety precautions should I take when working on the fuel system?What if the drain plug or pan threads are stripped?How tight should I torque the drain plug and oil filter?How do I tell if the oil change was successful after completing the job?How do I check for leaks after installation?Is it safe to drive the Mustang until repairs are done?Do I need new U-joints when installing an aluminum driveshaft?Will an aluminum driveshaft cause vibration?Do classic cars like a '65 Mustang need special diagnostic tools?Is an aluminum driveshaft safe for a high-power street or race car?Do I need to replace the entire wiring harness?Do I need a special wiring harness to install an aftermarket radio?Could a slipping clutch cause the symptoms shown in the video?Is welding on the driveshaft safe?Do I need to shorten or modify the driveshaft for my '65 Mustang?Will a modern Bluetooth head unit physically fit in a 1965 Mustang dash?Do I need to rebuild the carburetor if the car runs rough?Can I reuse the old fuel sending unit?How long does a basic dash rewire typically take?What safety steps should I take before working under the Mustang?Can I use toggle switches for all dash functions?What are the most common causes of intermittent fuel pressure loss on a classic Mustang?How should I prioritize repairs after the test drive?How long does a fuel tank replacement on a '65 Mustang typically take?What sized hose and fittings do I need?What safety precautions are important when working with the fuel tank?What should I check first if a classic car runs poorly on a test drive?What engine and drivetrain are in the car?Can I replicate these modifications as a DIYer?How do I document problems during a test drive to make diagnosis easier later?
Parts (69)
Tools (66)